The TE series is used wherever large volumes of air need to be extracted with rooftop applications in the absence of ductwork. The construction of this series, equipped with UNEL-MEC motors, ensures long-term robustness and reliability, allowing for eventual replacement or repair of the motors, all of which are unified and built to international standards. Operating temperature : -25°C/+40C°
Drum with double edge with large radius of curvature and support base made of sheet steel, painted with baked epoxy-polyester powders
Protective cap made of weather-resistant technopolymer
Weather-protected outer steel rod safety net in accordance with UNI EN 294 standard
Impeller with technopolymer blades (standard) and aluminum hub, statically and dynamically balanced in accordance with UNI ISO 1940/BS 6861/1 standard with variable shrinkage angle from stationary
Three-phase or single-phase asynchronous motor, EEF 1 and 2 efficiency, suitable for operation by speed regulation, IP 55 protection, class F insulation, S1 service, execution 4, conforms to IEC/EEC specifications (UNEL -MEC)
On request:
TE INOX - Version with stainless steel taburo.
TE ALL. - Version with aluminum drum
TE 2V - Version with three-phase double speed TE INV motorisation. - Reverse flow inlet version
TE REV - Version with reversible flow
IMPORTANT: In the absence of a gravity damper, the impeller-side safety net will be fitted as standard to meet current accident prevention regulations
Accessories
- Cerebro and/or Easy series electrical panel
- Speed controller (single-phase)
- Suction gravity damper
- Wall-mounted sub-base
- Silencer in suction
- support base for corrugated cover
Technical characteristics
kW
1,1
Voltage
3PH
Current (A)
2,8
Polarity or No. turns at 1'
4
Type of controller
QE Cerebro / Easy
Dimensions
B x D x H (mm)
930x930X500
Hole spacing "B x B" (mm)
870X870
No. of holes x mm
NO.4X10MM
Air passage "D" diameter mm
640
Weight KG
58
CIMI Srl reserves the right to change dimensional dimensions and/or performance for improvements or range changes without what is on the site being binding.
The reported data meet the following parameters:
- Tolerance on flow rate ±5%
- Noise tolerance +3dB(A)
- Air temperature 15°C
- Barometric pressure 760 mm Hg
- Air specific gravity 1.226 kg/m³
- Frequency 50 Hz
Sound pressure level was measured by omnidirectional free-field measurement at 1.5 or 3 m (depending on the product) from the fan with ducted inlet, tolerances, performance points and environments according to European standards.
Data Sheet
MAIN FEATURES
TECHNICAL FEATURES
DIMENSIONS
Accessories
"CIMI Srl reserves the right to change dimensional dimensions and/or performance for improvements or range changes without what is on the site being binding. The data shown comply with the following parameters: Flow rate tolerance ±5% | Noise tolerance +3dB(A) | Air temperature 15°C | Barometric pressure 760 mm Hg | Air specific gravity 1.226 Kg/m³ | Frequency 50 Hz The sound pressure level was measured with omnidirectional free-field measurement at 1.5 or 3 m (depending on the product) from the fan with ducted inlet, tolerances, performance points and environments according to European standards."
Drum with double edge with large radius of curvature and support base made of sheet steel, painted with baked epoxy-polyester powders
Protective cap made of weather-resistant technopolymer
Weather-protected outer steel rod safety net in accordance with UNI EN 294 standard
Impeller with technopolymer blades (standard) and aluminum hub, statically and dynamically balanced in accordance with UNI ISO 1940/BS 6861/1 standard with variable shrinkage angle from stationary
Three-phase or single-phase asynchronous motor, EEF 1 and 2 efficiency, suitable for operation by speed regulation, IP 55 protection, class F insulation, S1 service, execution 4, conforms to IEC/EEC specifications (UNEL -MEC)
On request:
TE INOX - Version with stainless steel taburo.
TE ALL. - Version with aluminum drum
TE 2V - Version with three-phase double speed TE INV motorisation. - Reverse flow inlet version
TE REV - Version with reversible flow
IMPORTANT: In the absence of a gravity damper, the impeller-side safety net will be fitted as standard to meet current accident prevention regulations
The TE series is used wherever large volumes of air need to be extracted with rooftop applications in the absence of ductwork. The construction of this series, equipped with UNEL-MEC motors, ensures long-term robustness and reliability, allowing for eventual replacement or repair of the motors, all of which are unified and built to international standards. Operating temperature : -25°C/+40C°
- Cerebro and/or Easy series electrical panel
- Speed controller (single-phase)
- Suction gravity damper
- Wall-mounted sub-base
- Silencer in suction
- support base for corrugated cover
