The particular application of the DF series is for air mixing in all those facilities where the phenomenon of de-stratification of heat and humidity is to be eliminated, benefiting the health of the operators and reducing energy waste. The construction of this series, equipped with adjustable motors at low speeds, prevents the formation of cold air currents on the ground. - Operating temperature : -25°C/+40°C
- Wide-radius steel plate drum and diffuser painted with baked epoxy-polyester powders
- Impeller with techno-polymer airfoil blades and aluminum hub, statically and dynamically balanced according to UNI ISO 1940/BS 6861-1 standard
- Fixing chains complete with support bracket
- Three-phase or single-phase asynchronous motor suitable for operation by single-phase speed regulation
- IP 55 protection class F insulation.
It is advisable to install diffusers with speed controllers equipped with a thermal probe or with an automatic control panel, with a temperature set at the thermostat of not less than 20°C in order to avoid the movement of cold air. - Proper installation involves covering the affected area using one destratifier per 200/250 square meters.
Accessories
- Speed controller (single-phase)
- Digital thermostat with probe
- Automatic control panel for speed and temperature control
Technical characteristics
kW
0,14
Voltage
1PH
Current (A)
2
Polarity or No. turns at 1'
650
Type of controller
RV3A
Dimensions
B x D x H (mm)
900X900X200
Air passage "D" diameter mm
800
Weight KG
32
CIMI Srl reserves the right to change dimensional dimensions and/or performance for improvements or range changes without what is on the site being binding.
The reported data meet the following parameters:
- Tolerance on flow rate ±5%
- Noise tolerance +3dB(A)
- Air temperature 15°C
- Barometric pressure 760 mm Hg
- Air specific gravity 1.226 kg/m³
- Frequency 50 Hz
Sound pressure level was measured by omnidirectional free-field measurement at 1.5 or 3 m (depending on the product) from the fan with ducted inlet, tolerances, performance points and environments according to European standards.
Data Sheet
MAIN FEATURES
TECHNICAL FEATURES
DIMENSIONS
Accessories
"CIMI Srl reserves the right to change dimensional dimensions and/or performance for improvements or range changes without what is on the site being binding. The data shown comply with the following parameters: Flow rate tolerance ±5% | Noise tolerance +3dB(A) | Air temperature 15°C | Barometric pressure 760 mm Hg | Air specific gravity 1.226 Kg/m³ | Frequency 50 Hz The sound pressure level was measured with omnidirectional free-field measurement at 1.5 or 3 m (depending on the product) from the fan with ducted inlet, tolerances, performance points and environments according to European standards."
- Wide-radius steel plate drum and diffuser painted with baked epoxy-polyester powders
- Impeller with techno-polymer airfoil blades and aluminum hub, statically and dynamically balanced according to UNI ISO 1940/BS 6861-1 standard
- Fixing chains complete with support bracket
- Three-phase or single-phase asynchronous motor suitable for operation by single-phase speed regulation
- IP 55 protection class F insulation.
It is advisable to install diffusers with speed controllers equipped with a thermal probe or with an automatic control panel, with a temperature set at the thermostat of not less than 20°C in order to avoid the movement of cold air. - Proper installation involves covering the affected area using one destratifier per 200/250 square meters.
The particular application of the DF series is for air mixing in all those facilities where the phenomenon of de-stratification of heat and humidity is to be eliminated, benefiting the health of the operators and reducing energy waste. The construction of this series, equipped with adjustable motors at low speeds, prevents the formation of cold air currents on the ground. - Operating temperature : -25°C/+40°C
- Speed controller (single-phase)
- Digital thermostat with probe
- Automatic control panel for speed and temperature control
